Search results

  1. G. Shahan

    Crown stag utility

    Nice one Ray. Greg
  2. G. Shahan

    Recently completed knife for a fellow Knife Dog

    I like it a bunch, doesn't matter what you call it. Greg
  3. G. Shahan

    "Flaming Rose" Mosaic Fighter

    Very Nice Graham!!! Greg
  4. G. Shahan

    Iron wood and copper

    Just finished this one. Not sure how I got those other two pics in here, but I cant seem to get rid of them. Thanks for lookin, Greg
  5. G. Shahan

    Elmax Build n Test n Show Thread

    Thank you Ironwolf and Pieter For your kind words, they are more appreciated much more than you know. Greg
  6. G. Shahan

    Elmax Build n Test n Show Thread

    Finished knife Had to dig this one up from way back. I finished this just in time to give it to my son inlaw for Christmas. Hope you dogs like it. Greg
  7. G. Shahan

    Servicemember Knife Build "Recruiting Drive"

    Sent mine out this morning Greg
  8. G. Shahan

    Elmax Build n Test n Show Thread

    Well my wife took off with my camera and left it at a friends house so I dont have pics. I tested my Elmax knife a few days ago and am impressed. Chopped 2x4's, chopped tree branches, then sliced up three cardboard boxes. Still shaving sharp at this point. Chopped more 2x4's, chopped more...
  9. G. Shahan

    Elmax Build n Test n Show Thread

    Yes Sir I plan to give it a work out. My grandson picked these scales.
  10. G. Shahan

    Elmax Build n Test n Show Thread

    Thanks for the comments fells, Carey, I use a two inch wheel, at the wide part of the tang I move the grind up and down to be about 3/16 from the edges. So far this steel is pretty much straight forward to work with. After heat treat its TOUGH to grind and VERY TOUGH to hand sand. It...
  11. G. Shahan

    Elmax Build n Test n Show Thread

    Okie dokie, Out of the super duper hillbilly cryo tank. Two hours twice at 400 F. Back to the grinder to take the bevels a little higher and thinner. Next to taper the tang, I use a 50 grit blaze and run it as fast as my grinder will run, then a new 120 at a slower speed. I am making this...
  12. G. Shahan

    Elmax Build n Test n Show Thread

    Here we go, got my HT recipe, SS foil (I hate this stuff) and my oven programed. Plate quenched, then its off to the hillbilly cryo tank.
  13. G. Shahan

    Elmax Build n Test n Show Thread

    Thanks Gents, This is what I did tonite. Drilled holes and hollow ground tang. Didnt drill to hard I didnt think. I always taper my tangs after heat treat, hope thats not a mistake with this stuff. My oven is busy with some 1080 at the moment so HT will be tomorrow. Greg
  14. G. Shahan

    Elmax Build n Test n Show Thread

    I got around to working on my chunk of ELMAX. So far it seems pretty nice to work with, cuts and grinds nice. Havent drilled any holes yet. Here is what I have so far.
  15. G. Shahan

    Servicemember Knife Build "Recruiting Drive"

    I got my blank yesterday. Its ground and ready for heat treat today. Greg
  16. G. Shahan

    Servicemember Knife Build "Recruiting Drive"

    Hey Bill T. Got an empty envelope in the mail today. The end was ripped out and all the contents are gone.
  17. G. Shahan

    Servicemember Knife Build "Recruiting Drive"

    Hey Murph, and Justin, Sign me up. I would be glad to pay for all my materials, heat treat and shipping. I'll pay for a kydex sheath. I have no clue or experience with kydex. And I'll need a time frame. Greg
  18. G. Shahan

    Bufflo Hunter

    Art, You are a "stud" Knife maker. Greg
  19. G. Shahan

    I'll be down a few days......Prayers needed

    Prayers brother, Greg
  20. G. Shahan

    Free Burl Every Saturday

    Hey Mark, I'm in. Thanks, Greg
Back
Top