Morland Picture Gallery

Knife No. 149 is complete. It does need sharpened. A fillet knife made from 440c. 5.5 inch blade. Desert ironwood, whitetail deer antler, brass guard, spacers and pins. Lined and braided leather sheath. And for John Wilson a fish on the sheath.

5245-A953-EDB4-4-B97-9-DB6-7277-D55-B349-A.jpg


FAC51-CB6-E8-C9-446-D-87-BB-DB77-C665-D092.jpg


D298545-C-1-B0-E-46-FC-8-C63-EF284-A7-C46-E7.jpg


BC476-AE0-63-C9-4-CEA-97-C1-41184-D1-BF74-A.jpg


76872354-8529-4-BF6-B1-C3-F0-DE783946-FB.jpg


0-CF77-DFC-1972-4-E83-A177-B5464-DD5-EAAD.jpg
 
Hi Dennis remember how I asked you how you peened your pins in that cleaver? Well I finally finished the project I asked that for. This is my spotted ducky kiradashi. Thank you!15862003023537173006216765482436.jpg
 
Hi Dennis remember how I asked you how you peened your pins in that cleaver? Well I finally finished the project I asked that for. This is my spotted ducky kiradashi. Thank you!View attachment 72731


Aiden

That is a cool little cutter. Looks like they all piened fairly well. I see one of the rear pins has a broken piece in the handle. Second from top. Otherwise, all the others look good.

Might I ask, what is the intended task for the knife. A friend of mine has a carpet knife that looks similar is why I ask.

Dennis
 
Aiden

That is a cool little cutter. Looks like they all piened fairly well. I see one of the rear pins has a broken piece in the handle. Second from top. Otherwise, all the others look good.

Might I ask, what is the intended task for the knife. A friend of mine has a carpet knife that looks similar is why I ask.

Dennis
Thanks Dennis,
That one I cut a little too short, so it couldn't reach into all the corners, (of the circular hole:)). I should have drilled it out and repeened it. It was originally designed to be pretty much a utility knife. One of his brothers is my favorite for leather work. I think the design needs some work, it is an old design. But they are fun and pretty fast to make, so I still like to do them.
 
Knife No. 150. It is a good one. A rare kitchen knife and fork. Made from 440c. I started this years ago. Michael Miller did the heat treat for me before I had an oven. These have my old stamp on them. Almost vintage. Brass bolsters, stabilized walnut scales, g10 spacers, brass pins, and a very nice walnut storage box. The walnut is from my fathers sawmill. The recipient of this knife will be his niece, my cousin. I hope it becomes an heirloom.

7-FEFFB0-A-4530-4-F92-955-F-5-E7-B2-D2-A2587.jpg


9-EF22-D5-F-3858-402-A-BF8-E-67-ECEA4-AB0-DF.jpg


F07-E8-B61-F9-C6-4-D47-94-A5-6769-D0395-B97.jpg


33705562-9-A0-C-4-E0-C-BA4-D-FA59-BE850-E51.jpg


C4-C30-BA8-8-AB3-4-EB8-B046-280-D6-BF733-D3.jpg
 
Dennis, when you've made forks do you heat treat them? I've thought several times about making a knife and fork set.
 
Thanks for the reply Dennis. I suspected so, but wasn't sure.

Sean I sent these out for heat treatment years ago. They have been sitting in a drawer begging for some attention. Michael Miller heat treated them for me. They are hard. I find stainless to be way harder to finish compared to carbon.
 
Back
Top