Recent content by percy

  1. P

    Battleship Knives

    here are some of the GEC 35 Battleship knives they did for me this year. these are forged of steel from the ships and some have decking for handles. Some of the ships did not have wooden decks, so we used wood from other ships. Let me know what you think. These are $300.00 I pay shipping in US...
  2. P

    600 Grit Belts?

    I use the norax and they work for me. I understand it changes with everyone for sure. Mainly Ed I wanted to tell you I understand about the Pupus. My wife has it and sometimes it is horrifying. She is such a warrior and most of the time you don't know how bad it affects her unless you look into...
  3. P

    410 ss straightening

    I bought part of a sheet of 410 ss 3/16 thick. I am going to use it to mill folder frames from. I had some strips water jet cut for me and they warped. Not a lot but enough. How would be the best way to straighten them or flatten them out. I tried surface grinding but the magnet sucks them back...
  4. P

    shields

    I bought some shields and cutting pattern from a guy in Fla. a few years ago. I need some more but can't find my info to contact him. I was hoping someone on here can help me out with this. Thanks in advance.
  5. P

    Kevin did you ever do a book on knife maker heat treating receipes

    Kevin did you ever do a book on knife maker heat treating receipes
  6. P

    Little Giant value

    I have been busy and haven't looked back to see the responses. This hammer was rebuilt by Uncle Al's machine shop in Arkansas. He said it was like new now but I haven't gone and picked it up as I am going to wait until the next knifemakers get together up there. I was only wondering a price...
  7. P

    Little Giant value

    Can anyone give me a ball park value on a Little Giant 50# that has been completely reworked by Uncle Al's Machine shop in Arkansas. It is in like new condition with new dies, motor, and all else. Thanks in advance for the info
  8. P

    Little Giant value

    Can anyone give me a ball park value on a Little Giant 50# that has been completely reworked by Uncle Al's Machine shop in Arkansas. It is in like new condition with new dies, motor, and all else. Thanks in advance for the info
  9. P

    Advice on nail nick

    You can get the little chop saw from Harbor Freight it cost about 29.00. It takes a three inch blade. Take the blade off and get the three inch wide cut off wheel and use a cheap diamond sharpener to shape it at and angle and then you can put your knife blades in the vise on the saw and grind...
  10. P

    Thermocycle for CPM-154 and other stainless type steels

    Would doing a cycle like this help CPM steels. I know with forging it is a good idea but was wondering about this part. Any help or info would be appreciated.
  11. P

    Blade show exibitor - How to set up?

    Just today I received a notice from intuit that they will no longer let me sale knives using the intuit but it could be or go pay. I checked and my card reader is no longer working. This was done because they said the knives were weapons. 4 years ago I went to intuit because square did the same...
  12. P

    Hello From TEXAS

    Johnny Stout at stoutknives.com
  13. P

    A type of wood I dont know please assist

    Kindly looks like one of the Locust species. Good luck.
  14. P

    BladeBond Epoxy Pigments---Now Available

    Thanks for the info you did on the System Three verses your product. Like I said I have been using it for years with no problems. However that being said I would much rather use a product that the company supports the knife industry. Cost is not the issue even if yours is more it will be my next...
  15. P

    BladeBond Epoxy Pigments---Now Available

    How does this compare to the System 3 epoxies that I have been using. The T-88 or G-2 and the Gel magic. I think they are water proof as well since they are being made for the marine industry. I am always interested in new products especially when those companies support the knife industry.
Top